Approvals and Certification

ZigBee Alliance - Profile Certification

Telegesis has successfully achieved certification based upon the ZigBee PRO feature set of the ZigBee standard. Telegesis was granted ZigBee certification for their Manufacturer Specific Profile (MSP). This makes the Telegesis ETRX2 the world's first ZigBee PRO compliant module.

FCC approvals

ETRX1 - FCC ID: S4GETRX1
ETRX2 - FCC ID: T7VEM250A
ETRX2-PA - FCC ID: T7VEM250B

The ETRX2 has been designed to meet most national regulations for World-wide use. Using the integrated antenna it conforms to FCC CFR 47 Part 15 (USA).

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The ETRX2 / ETRX2-PA device carries FCC authorization and is marked with the FCC ID Number. Whilst any device into which this authorized module is installed will not normally be required to obtain FCC authorization, this does not preclude the possibility that some other form of authorization or testing may be required for the finished device.

When the ETRX2 module is integrated inside another device/product, then the outside surface of that device/product must display a label referring to the enclosed module. This exterior label can use wording such as "Contains Transmitter Module FCC ID: T7VEM250A" or "Contains FCC ID: T7VEM250A" although any similar wording that expresses the same meaning may be used. This module complies with the USA SAR requirements and is not intended to be operated within 20cm of the body. The following statement must be included as a CAUTION statement in manuals for OEM products to alert users on FCC RF exposure compliance:

"WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operations at closer distances than this are not recommended."

European Certification R&TTE

ETRX2

With the integrated antenna the ETRX2 has been tested and conforms to the following standards:

Radio: ETSI EN300 440-2 V1.1.1(2001-09)
Radio: ETSI EN300 328 V1.6.1(11/2004)
EMC: ETSI EN301 489-17 V1.2.1 (08/2002)
Safety: ETSI EN60950-1:2001+A11:2004

ETRX2-PA

With the integrated antenna, 1/2 Wave and Stubby 1/4 wave antenna, the ETRX2 has been tested and conforms to the following standards:

* Radio: ETSI EN300 328 V1.7.1(10/2006)
* EMC: ETSI EN301 489-17 V1.2.1 (08/2002)
* Safety: ETSI EN60950-1:2006

If the ETRX2 / ETRX2-PA module is incorporated into an OEM product, the OEM product manufacturer must ensure compliance of the final product to the European Harmonised EMC, and low voltage/safety standards. A Declaration of Conformity must be issued for each of these standards and kept on file as described in the R&TTE Directive. The final product must not exceed the specified power ratings, antenna specifications and installation requirements as specified in this ETRX2 user manual. If any of these specifications are exceeded in the final product then a submission must be made to a notified body for compliance testing to all of the required standards.

The ‘CE' marking must be applied to a visible location on any OEM product. For more information please refer to http://ec.europa.eu/enterprise/faq/ce-mark.htm. Customers assume full responsibility for learning and meeting the required guidelines for each country in their distribution market.

Declarations of Conformity

Telegesis (UK) Ltd has issued Declarations of Conformity for the ETRX2 and ETRX2-PA ZigBee RF Modules, which cover Radio Emissions, EMC and Safety which are available for dowload below.